Brother scanner ads 4300n12/11/2023 ![]() With USB3.0 and USB host, you can securely scan documents without the need for a PC.Įnjoy effortless and impressive image capture and processing - from easily referencing and locating scanned pages with the digital imprinter, to optimising image quality through the automatic vertical streaks and moiré reduction tools. With an in-built ultrasonic multifeed sensor to eliminate misfeeds, the ADS-4300N also has a large 80 sheet ADF capacity and rapidly scans up to 40ppm. Remove the USB flash drive so that the computer does not detect it.Professional desktop scanner with wired connectivityĬonnect the Brother ADS-4300N A4 document scanner to your network and effortlessly capture your documents to share and collaborate with colleagues. The computer detects the USB flash drive that is inserted into the machine. The computer has detected a USB flash drive.Ī USB flash drive is inserted into the machine and the computer is connected to the machine using a USB cable. Press to delete the entered information, and then enter the correct information. Stop configuring the machine from the Control Panel.Ī USB flash drive is inserted into the machine.Ĭannot enter the IP address and Subnet Mask. The machine is being configured from the machine’s Control Panel. Wait until scanning has finished and try again. The machine is not connected to your computer.Ĭonnect the machine to your computer, and then try again.Ĭlear all errors, check the status is Ready on Remote Setup and then try again. Wait until the machine finishes processing, and then try again. Select the Remove Bleed-through / Pattern / Remove Background Colour check box.Ĭannot save the settings in Remote Setup or Web Based Management. The settings are not appropriate for the type of document being scanned. Paper dust has accumulated on the surface of the glass strips inside the machine.īleedthrough is seen in the scanned data. Set the Extendable Output Tray according to the length of the document. The Extendable Output Tray is not set to the correct length. Set the Document Separation Switch to (Manual Single Mode) and scan again. The Document Separation Switch is set to (Continuous Feed Mode) when scanning documents folded in half, envelopes, or Multi-Layered Transfer Paper. See Related Information: Acceptable Documents. Make sure your document is acceptable for the machine. Your document is not acceptable for the machine. Set the Document Separation Switch to (Continuous Feed Mode) and scan again. The machine fed multiple documents but scanned only the first document.ĭocument Separation Switch is set to (Manual Single Mode). Make sure your media is acceptable for the machine. Remove any foreign objects or ripped paper from the ADF. Make sure you do not exceed the ADF's capacity. Too many documents are loaded in the ADF at a time. See Related Information: Clean the Scanner and Rollers. ![]() Paper dust has accumulated on the surface of the Pick Up Roller or Brake Roller.Ĭlean the Brake Roller and Pick Up Roller. ![]() The resolution is not appropriate for your document.Īdjust the data transfer rate in the Optimize Data Transfer menu of the TWAIN driver or in Brother iPrint&Scan. Straighten the curled document and scan again. If you use a preset document size, the document skewing cannot be corrected automatically. Make sure the document size settings are appropriate for your document.Ĭonfigure the margin settings and adjust the scanning position. ![]() For example, a Letter/A4-sized document was fed when Executive/A5 was selected as the document size. The settings are not appropriate for your document. If the document does not feed straight, use the Continuous Scan option. When Scan Size is set to Auto and you are scanning a document that contains multiple page sizes, insert narrow pages straight and as close to the centre of the machine as possible. Gently adjust the Paper Guides to fit the width of your document. The Paper Guides are not adjusted to fit the width of the document. Paper dust has accumulated on the surface of the glass strips.Ĭlean the glass strips inside the machine. Vertical lines are seen in the scanned image. Make sure the Brother TWAIN driver is selected as the primary source in your application. The TWAIN driver has not been selected as the primary source in your scanning application. TWAIN errors appear when starting to scan. For example, in Nuance ™ PaperPort ™ 14SE, click Scan Settings > Select. Make sure the Brother TWAIN or WIA driver is selected as the primary source in your scanning application. The TWAIN or WIA driver has not been selected as the primary source in your scanning application. TWAIN or WIA errors appear when starting to scan.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |